Welltech Dialogic SS7 Protocols ISUP Instrukcja Użytkownika Strona 54
- Strona / 203
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Section 6 Interface to Application
54
6.6 Application Messages from ISUP
The following table lists all application messages (message type
ISP_MSG_RX_IND) sent by ISUP module to the user application:
Table 1. All Application Messages sent by the ISUP Module to the User Application
Value Primitive Message
type
Dec Hex
Use
Alerting indication ACM
CPG
6
44
0x06
0x2c
Indicates outgoing called party being
alerted.
Application transport
indication
APM 65 0x41 Issued on receipt of an application
transport message.
Charge indication
(Generic)
CRG 50 0x32 Carries charging information
Circuit seized
indication
SZE 199 0xc7 Used for continuity checking and
indicates that a circuit has been seized
for an incoming call (but no address
information has yet been received).
Collection charging
indication
MPM 201 0xc9 Used to carry charging information.
Confusion indication CFN 47 0x2f Indicates that a confusion message
has been received.
Continuity indication COT 5 0x05 Indicates whether the continuity test
succeeded.
End-to-end message
indication
PAM 40 0x28 Conveys received end-to-end
message.
Facility confirmation FAA 32 0x20 Indicates that the remote party has
accepted the user to user service 3
request.
Facility indication FAR 31 0x1f Indicates that the remote party is
requesting user to user information
service 3 during the active phase of a
call.
Forward transfer
indication
FOT 8 0x08 Indicates that a forward transfer
message has been received.
SAM 2 0x02 Subsequent address digits for overlap
signaling.
Information indication
INF 4 0x04 Provides additional call information.
Identification
indication
IDR 54 0x36 Used to request an action regarding
the MCID supplementary service.
Identification
confirmation
IRS 55 0x37 Used to respond to the IDR message.
Loop back
acknowledgement
indication
LPA 36 0x24 Indicates to the application that a
continuity check loop has been applied
to the circuit.
Loop prevention
indication
LOP 64 0x40 Use with ECT supplementary service.
- Dialogic 1
- SS7 Protocols 1
- Contents 3
- Figures 6
- Revision History 7
- About this Publication 9
- 1.3 Related Documentation 10
- 1.4 Feature Overview 11
- 2 General Description 13
- Value Mnemonic Meaning 14
- 3 Internal Data Structures 17
- 4.1 System Functions 19
- 4.2 Timer Operation 19
- 5 Interface to MTP 21
- Section 5 Interface to MTP 22
- 6 Interface to Application 23
- 6.2.2 Receive Indication 24
- 6.5.1 Alerting Request 28
- 6.5.6 Confusion Request 32
- 6.5.7 Continuity Request 32
- 6.5.9 Exit Request 33
- 6.5.10 Facility Request 33
- 6.5.11 Facility Response 35
- 6.5.15 Information Request 37
- 6.5.19 Overload Request 40
- 6.5.21 Proceeding request 41
- 6.5.22 Progress Request 42
- 6.5.23 Release Response 43
- 6.5.24 Release Request 44
- 6.5.26 Resume Request 45
- 6.5.27 Segmentation Request 46
- 6.5.28 Setup Request 46
- 6.5.29 Setup Response 49
- 6.5.31 Suspend Request 52
- 6.6.1 Alerting Indication 56
- 6.6.6 Confusion Indication 60
- 6.6.7 Continuity Indication 61
- 6.6.9 Exit Indication 61
- 6.6.10 Facility Indication 62
- 6.6.11 Facility Confirmation 63
- 6.6.19 Overload Indication 68
- 6.6.21 Proceeding Indication 69
- 6.6.22 Progress Indication 70
- 6.6.23 Release Confirmation 71
- 6.6.24 Release Indication 71
- 6.6.26 Resume Indication 73
- 6.6.28 Setup Confirmation 74
- 6.6.29 Setup Indication 76
- 6.6.31 Suspend Indication 79
- 6.7 Parameter Definitions 80
- 6.7.1 Called Party Number 86
- 6.7.2 Calling Party Number 86
- 6.7.3 Cause Indicators 87
- 6.7.4 Custom Parameter 88
- 6.7.5 Message Data 88
- 6.7.7 Tariff Type 89
- 6.7.8 Unrecognised Parameter 90
- 6.8.3 Hop Counter Procedure 94
- 6.8.4 Continuity Testing 95
- Call Set Up 99
- Service 108
- 6.8.6 Message Segmentation 109
- 7 Management Interface 113
- reserved Set to zero 116
- 7.6 Local Overload Request 118
- Parameters 120
- 8 Non-Primitive Interface 121
- 8.3.1 Timer default values 138
- 8.5 Variant Initialisation 141
- operation 142
- message type 142
- 8.8 Read RAM Request 145
- 8.10 Read Circuit Request 146
- 8.11 Read Revision Request 146
- Section 150
- Event specific data 158
- Call states 164
- 8.22 Trace Event Indication 166
- A.1 German ISUP 171
- A.2 UK ISUP 172
- A.3 Japan (TTC) ISUP 173
- A.4 Nortel RLT 174
- A.4.2 Nortel RLT (ITU) 175
- A.5 Italian ISUP 176
- A.6 French ISUP 177
- A.7 China ISUP 178
- A.8 Finnish ISUP 180
- A.9 BICC 180
- Hex Dec Min Max 181
- Reference 181
- ISUP Module 183
- B.2 ITU-T Parameters 184
- B.3 ANSI T1.113 Messages 188
- B.4 ANSI T1.113 Parameters 189
- More Extended Options 195
- Appendix F: Timer Services 199
- F.1 Timer Expiry 200
- Variant Initialisation, 141 203
Powiązane produkty i podręczniki dla Komunikacja Welltech Dialogic SS7 Protocols ISUP
Komunikacja Welltech WG5290 Instrukcja Użytkownika
(149 strony)
(149 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji